KE3600 xDSL Multitester


At a glance

  • New, modern hardware design
  • ADSL1 to 2+ with Annex A/B/J/L/M
  • GbE-Port for Ethernet deployments
  • All important xDSL results at a glance
  • Dial-in, Ping and Trace Route w. IPv4/IPv6
  • Sunlight readable color TFT
  • High performance Lipo-Batt.
  • Management Software included
  •     
    Optional
  • VDSL2-Vectoring (ITU-T G.993.5)
  • ISDN UK0/S0- and POTS-Interface
  • Copper tests for line qualification up to 30 MHz
  • Software tools for IPTV and VoIP
  • GPON-Interface
  • xDSL Bonding (ITU-T G.998.1/2/3)
  • SHDLS 2- to 8-wire Interface
  • ISDN PRI S2M Interface

Availability on request

Questions? +49(0)7121-97550

info(AT)kurthelectronic.de

And again an ITC Product of the Year - our KE3600 is among the winners!!

Features
Technical Specifications
Optional Accessories
Delivery

The KE3600  is the  fast, easy-to-use and economical solution  for the installation and troubleshooting of DSL services  in hybrid ADSL1/2/2+/VDSL2 and bundled networks (capable for VDSL2 Vectoring and DSL Bonding).

Ensuring  the  highest  quality  triple-play  services  to  customers  is  a  must  for service providers, but  it  is also a challenge with an aging copper plant and  the need  to maximize  the use of all pairs  in  the cable bundle. Service providers can offer higher  rate/reach by implementing vectoring (ITU-T G.993.5) to take noise mitigation to the next level. Another industry standard method  that helps achiev-ing high-quality multiplay  is ADSL2+ and/or VDSL2 bonding (using two copper pairs as defined within ITU-T G.998.1,2,3) to increase the available data rates and/or the loop lengths to address a new customer service area.
These techniques are supported by the KE3600 to ensure consistency with service providers’ noise mitigation methods and procedures.

The xDSL and Ethernet ports make the KE3600 a flexible tool for qualifying services all the way  from  the central office  to  the customer's equipement.  It also provides powerful  troubleshooting applications that can be used in different modes to quickly isolate faults (network, outside plant, customer equipment or inside wiring). Even in hybrid networks, where FTTH is deployed,  the Ethernet ports can be used  inside  the home  to  test at any point.

KE3600  is  the perfect  tool  for any service provider deploying multiplay services over single-pair or bonded ADSL2+ and/or VDSL2.  Its  rugged design and easy-to-use menu make  it  the ideal tool for installation and repair technicians. With the KE3600, the testing process is highly automated and technicians close their jobs quickly and efficiently. The large display makes it even more user-friendly, and when it comes to saving results, it provides technicians with many connectivity options  for uploading  tests and compiling reports.

Note: Not all options described above are standard available for all KExxxx models.
Some functions are only available as a payable option.

Download xDSL Tester Info

___________________________________________________________________________________________ 

Optional
___________________________________________________________________________________________

 ISDN (BRI) /Analog (POTS) Interface

The optional ISDN / POTS interface checks all functions for the installation and maintenance of S0 and Uk0 and analog connections:

- Voltage measurement

- Terminal simulation TE

- Connection and self call tests

- Extensive service query

- Detailed information on the line status

- BER-Test for determining the bit error ratio

___________________________________________________________________________________________

 
Copper Tests with KECT Interface in one unit

The KE3600 offers with its internal KECT interface full support for prequalification and troubleshooting on the copper pair up to 30 MHz.

Digital Multimeter Measurements

- Current

- Isolation

- Resistance

- Capacitance

- Capacitive unbalance

- Loop analysis:
Editable , automated test sequence of the most important measurements

- KE900KE905 management functions:
Sends switching commands to the optional Remote Unit KE900/KE905 directly for comfortable remote switching of copper pairs at the far end of the line

xDSL Prequalification

Measurements on suitability for the intended application
xDSL system

- Impedance

- Attenuation

- Balance

- NEXT measurement

- Receive level

- Spectrum

- Wideband noise

- Impulse noise

___________________________________________________________________________________________

TDR functions
(only in conjunction with Copper Test Option)

The integrated TDR (Reflectometer) can detect and precisely localize any changes in impedance of the twisted pair, such as short circuit, disruption and water entry.

- Up to 6 km cable length with 0.5 mm ∅ 

- Adjustable pulse length, attenuation and zoom

- Dead zone only 3.80 m

- Detects joints, branches or stubs (bridge taps)

- Assessment of the cable

___________________________________________________________________________________________

VoIP Tests

- Terminal simulation

- VoIP connections over xDSL and Ethernet

- VoIP Signaling protocol SIP

- Call setup both with and without a registrar / proxy

___________________________________________________________________________________________

IPTV Tests

- Set-Top-Box-Emulation

- Review packages and switch-on and switching times

- Shows Bitrate and Jitter

- Preview function

Standards compliance

ADSL1/2/2+
ITU-T G.992.5 (ADSL2+ incl. Annex A, B, J, M)
ITU-T G.992.3 (ADSL2 incl. Annex A, B, J, L)
ITU-T G.992.2 (G.Lite incl. Annex A, B, J)
ITU-T G.992.1 (G.DMT incl. Annex A, B, J)
ATIS/ANSI T1.413 Issue 2
IEEE 802.3ah (PTM)
ITU-T G.998.1/2/3 (Bonding)*

VDSL2
ITU-T G.993.2 Annex A, B
ITU-T G.993.5 Vectoring
Profiles: 8a/b/c/d, 12a/b, 17a, 30a
Band Plan: 997, 998, US0
IEEE 802.3ah (PTM)
ITU-T G.998.1/2/3 (Bonding)*

DSL parameters
Maximum attainable bit rates
Actual achieved bit rates
Vendor code, revision
Actual bonded achieved rates
Interleave depth
Latency modes: fast, interleaved
Interleave delay
Data modes: ATM, PTM
Capacity (%)
Bit swapping
Signal-to-noise ratio (SNR) margin
INP
Output power
G.INP
Attenuation
Vectoring
Bits/bin
Modes: PTM, ATM, LOS, FEC, CRC, HEC
Attenuation/bin (Hlog/bin)
LATN per band
QLN/bin
SNR/bin
SATN per band

Test interfaces
VDSL2, ADSL 1/2/2+
Ethernet 10/100 MBit/s Management Port
Ethernet 10/100/1000 MBit/s Test Port 

Encapsulation methods
RFC 2684 supporting bridged Ethernet (IPoE) PPPoE (RFC 2516)
IPoA (RFC 1577) PPPoA/LLC and PPPoA/VC-MUX (RFC 2364)

Operating modes
DSL Terminate
Modem Replacement (DSL to Ethernet) Pass Through
Ethernet Terminate
Ethernet/Ethernet Pass Through

Login format
User name and password using PAP/CHAP

Connectivity support 
LAN/WAN status VLAN ID, VLAN tagging
DNS, gateway VPI/VCI
DHCP client/server, DHCP vendor class  IP release
NAT Signal Strength

Ping test
Ping destination: Gateway, IP adress or URL
Number of pings: 1 to 99
Packet size: 32 to 1200 bytes (default is 32)
Timeout: 1 to 10 seconds
Results: Packets sent/received, average round-trip delay (ms)
 
Traceroute test
Traceroute destination: Gateway, IP adress or URL
Timeout: In seconds, default is 1 s, maximum is 10 s
Packet size: 32 bytes
Number of hops: 1 bis 32 1 to 32 (default is 30)
Results: Indicates IP address of hop and round-trip time in milliseconds (ms)

FTP/HTTP speed test
Address: IP or URL
Direction: Upload and/or download
Results: Time, kB transferred, speed in kbit/s
Bookmarks: User-definable

Software options
Web Access
IPTV tests
VoIP tests

Interface options
xDSL Bonding Interface*
SHDSL 8-Wire-Interface
KECT3 Coppertest Interface for Line Qualification with DMM
TDR finds and localices cable faults (only with KECT3)
SFP-Port for Copper, Fiber (second GbE-Port) or GPON (ONT), Inserts optional
ISDN Uk0  / S / POTS Interface
S2M  Interface*

 *further information on request

General Data
Display
3.5 " TFT-Display, RGB 240 x 320

Power Supply
Built-in LiPo battery < 4 hours in full test mode, charging time < 6 hours

Size
23 x 11/9 x 7 cm

Weight
850 g

Housing
High impact resistant ABS with drop protection

Optional:

  • ISDN Uk0  / S / POTS Interface
  • KECT Coppertest Interface for Line Qualification with DMM
  • TDR finds and localizes cable faults (only with KECT3)
  • Software Option VoIP
  • Software Option IPTV
  • SFP-Port for Copper, Fiber (second GbE-Port), Inserts optional
  • SHDSL 2- to 8-Wire-Interface
  • GPON (ONT)*
  • xDSL Bonding Interface*
  • S2M  Interface*
  • AC Power supply and charger
  • Test leads RJ11-RJ45
  • RJ11-Banana plug with rubber insulated crocodile clips
  • Ethernet patch cable
  • Pouch made of rugged Cordura with additional space
  • Windows Software for download of results and upgrade of unit