KE501 Electric- Cable Finder Kit

General

high power output
cable tracking inside walls
precise pair identifying
over voltage protected up to 500V AC.
signal strength LED with noise filter
torch light build in

Put into the shopping basket

Please Log-In to use the shop. You don`t have a Log-In? Here you can register.

Questions? +49(0)7121-97550

info(AT)kurthelectronic.de

Features

Technical Specifications

Optional Accessories

Accessories

Recommend product

The KE501 Kit (EASYTEST500/PROBE510) improves speed and confidence in the installation and maintenance of wiring whether it is for power, telecommunication, alarm or control.

EASYTEST500 unit is fully protected to 400 Vac in TONE mode and up to 240 Vac in CONT mode, though it is not intended to be connected to live AC power lines for tracing. If the voltage on a connected line exceeds approximately 100 V the CONT LED will light as a warning.

EASYTEST500 can transmit either three continous tones (SOLID) or two alternating tones (ALT). The Solid or the Alt function is easily selected from the front panel using the ALT and SOLID buttons. An LED beside the button indicates the selected function. To start or stop the tone, first use the ON/OFF button to switch the unit on, then select the trace tone. The unit can be connected to send the trace tone to any kind of cable, including a live telephone line.

EASYTEST500 comes with removable alligator clips on banana plugs for ease of maintenance and substitution of other clip types. There is an optional modular adapter available for connecting to RJ11- and RJ45-type modular jacks.

When switched off EASYTEST500 will indicate the status of a connected telephone line including: service voltage presence and polarity, idle line, busy line, and incoming ringing. In the CONT position EASYTEST500 indicates short circuits (zero ohms to 100KOhm).

The capacitive PROBE510 is highly sensitive and works well with EASYTEST500 or any other tone generator to identify and trace wires or cables. The two-position HIGH and LOW volume switch is constructed with a highly dust and moisture resistant mylar membrane for easy, reliable operation. With the HIGH button depressed the PROBE510 can detect a traced cable at lateral distances of up to 100 cm. A more precise location of specific wires is usually done with the LOW button. No experimenting with volume control knobs is needed.

The probe’s conductive tip is molded of a plastic and carbon fiber composite, preventing shorts and other disturbances to lines. This composite probe tip is nearly unbreakable and is easily changed without opening the case. The slender shape allows high precision tracing of pairs, whether in tight bundles or high density wiring blocks.

The Probe510 has a special green LED indicator for use with Kurth EasyTest tone units. This indicator only lights when signals from EasyTest units are detected and has the effect of blocking interfering signals like power hum.

The bright, color-correct LED on the probe snout eliminates the need for a separate flashlight in dark spaces.

http://www.kurthelectronic.de/?id=Download Datasheet

EASYTEST500

Gehäuse / Housing :
Stabiles und schlagfestes wetterbeständiges ABS-Gehäuse mit Silikon Betätigungstasten / Heavy duty water resistant housing made from ABS, elastomeric silicon rubber push button switches.

Prüfschnüre / Test Leads: 35 cm lange Prüfschnüre aus flexiblem PVC mit Bananensteckern und extra starken Krokodilklemmen. Durable wire leads, 35cm long, with banana plugs and extra solid alligator clips

Vier Frequenzen wählbar / Four frequencies selectable :
1. SOLID: 1000 Hz
2. ALT: 1000/800 Hz
3. SOLID: 2600 Hz
4. ALT: 2600/1900 Hz
Genauigkeit / Accuracie < +/- 1% (Quartz)

Low Batt - Anzeige durch blinkende LED
Low Batt indication by flashing LED

Automatische Abschaltung nach 45 Minuten
Auto shut Off after 45 minutes

Deaktivierung der Abschaltung
Auto shut Off override
Anzeige der Deaktivierung durch blinkende LED
Auto shut OFF override indication by
flashing LED

Überspannungsschutz / Over Voltage Protection :
Bis zu 400V AC / DC in jeder Betriebsart max. 15 Minuten
Up to400V AC / DC in any Mode max. 15 minutes

Suchentfernung zum Kabel / Trace Distance to Cable/Wire :
Bis zu 60 cm / Up to 15” (60cm)

Maximale Kabellänge / Trace Cable Length :
Bis zu 15 km ohne Belastung / Up to 15 km (no load)

Hohe Sendeleistung (Batterie 9,2V) / High Power Output (Battery 9,2V) :
9,0V SS ohne Last / 9,0V PP no load
10 dBm into 600 Ohm
9 dBm into 100 Ohm
7,5 dBm into 50 Ohm
Ton auf kurzgeschlossener Ader bis 250 m
Tone over shorted pair up to 250 m. (Inhouse)

Weitere Leistungsmerkmale / Other Specifications:
Goldbeschichtete Kontakte
Gold Plated Contacts
Gerät Einschaltkontrolle mit LED
Unit ON - Indication by LED
Anzeige ALTernierende Frequenz mit blinkender LED
Indication of ALTernating Frequency by blinking LED
Anzeige SOLID Frequenz mit LED stehender LED
Indication of SOLID frequency by steady LED
Zugentlastung der Prüfschnüre
Test leads protected by rubber - strain Relief
Getrenntes Batteriefach
Separate Battery Compartment

Batterie / Battery :
9V alkaline - Batterie >100 Stunden Lebensdauer
9V Alkaline, >100 hrs battery life

Abmessungen / Dimensions :
68 x 96 x 25 mm / 2.68” x 3.75” x 1.0”

Gewicht / Weight :
150g ohne Batterie / 2.4 oz (150g) without Battery

PROBE510
Gehäuse / Housing :
Solides, schlagfestes und wasserfestes ABS - Gehäuse
Heavy duty water resistant housing made from ABS.

Leistungsmerkmale / Specifications :
Nichtleitende Prüfspitze aus Kohlefaserverstärktem Kunststoff / Non-conductive solid carbon fiber tip
3,5 mm Kopfhörerbuchse
3.5 mm Earphone Jack
Goldbeschichtete Kontakte
Gold Plated Contacts
Getrenntes Batteriefach
Separate Battery Compartment

Batterie / Battery :
9V Alkaline Batterie >100 Stunden Lebensdauer
9V Alkaline, >100 hrs battery life

Abmessungen / Dimensions :
220 x 40 / 34 x 25 mm
8.7” x 1.57” / 1.34” x 0.98”

Gewicht / Weight :
80g ohne Batterie
1.28 oz (80g) without Battery

EASYTEST500
Gehäuse / Housing :
Stabiles und schlagfestes wetterbeständiges ABS-Gehäuse mit Silikon Betätigungstasten / Heavy duty water resistant housing made from ABS, elastomeric silicon rubber push button switches.