User login
KE701 TelCo- Cable Finder Kit
The KE701 Kit (EASYTEST720/PROBE410) improves speed and confidence in the installation and maintenance of wiring whether it is for power, telecommunication, alarm or control.
EASYTEST720 can transmit either three continuous tracing tones (SOLID) or two alternating tones (ALT). The Solid or the Alt function is easily selected from the front panel using the ALT and SOLID buttons. An LED beside each button indicates the selected function. To start or stop the tone, first use the ON/OFF button then select the trace tone. The unit can be connected to send the trace tone to any kind of cable, including a live telephone line. The unit is protected to 400 Vac in TONE mode and up to 240 Vac in CONT mode.
EASYTEST720 provides durable alligator clips and snag-proof modular plugs for both RJ11 and RJ45 with strain relief for reliability. The special RJ11 modular plug has protection slots for pins 1 and 8 that will fit RJ45 jacks without damaging them. If the RJ45 plug is inserted into an active LAN jack in the DATA mode, the DATA LED will pulse brightly, and the associated link activity light on the conventional LAN hub or switch will begin to blink. In the CONT position EASYTEST720 leads and RJ11 plug will indicate short circuits (zero ohms to 100KOhm).
When switched off EASYTEST720 will indicate the status of a connected telephone line including: service voltage presence and polarity, idle line, busy line, and incoming ringing.
The capacitive PROBE410 (U.S. PROBE310) is highly sensitive and works well with EASYTEST720 or any other tone generator to identify and trace wires or cables. The two-position HIGH and LOW volume switch is constructed with a highly dust and moisture resistant mylar membrane for easy, reliable operation. With the HIGH button depressed the PROBE410 can detect a traced cable at lateral distances of up to 100 cm. A more precise location of specific wires is usually done with the LOW button. No user experimentation with volume control knobs is needed. The additional red DATA LED allows the detection of active ISDN BRI (UK0) lines without any additional equipment (only Probe410).
The Probe410 has a special green LED indicator for use with Kurth EasyTest tone units. This indicator only lights when signals from EasyTest units are detected and has the effect of blocking interfering signals like power hum. The bright, color-correct LED on the probe snout eliminates the need for a separate flashlight in dark spaces.
The probe’s conductive tip is molded of a plastic and carbon fiber composite, preventing shorts and other disturbances to lines. This composite probe tip is nearly unbreakable and is easily changed without opening the case. The slender shape allows high precision tracing of pairs, whether in tight bundles or high density wiring blocks.
To increase audibility or reduce noise the Probe410 can be used with the optional, light-weight earpiece.
EASYTEST720
Gehäuse / Housing :
Stabiles und schlagfestes wetterbeständiges ABS-Gehäuse mit Silikon Betätigungstasten / Heavy duty water resistant housing made from ABS, elastomeric silicon rubber push button switches.
Prüfschnüre / Test Leads: 25 cm lange Prüfschnüre aus flexiblem PVC mit 4mm Bananensteckern, eine Prüfleitung mit Modularstecker RJ11 und Rj45 mit Knickschutz (25cm) durable wire leads with 4mm bananaplugs and one with a special long modular plug RJ11 and Rj45 and latch protection
Vier Sinus - Frequenzen wählbar / Four Sine- wave Frequencies selectable :
1. SOLID: 1000 Hz
2. ALT: 1000/800 Hz
3. SOLID: 2600 Hz
4. ALT: 2600/1900 Hz
Genauigkeit / Accuracie < +/- 1% (Quartz)
Dataport LINK-Blink Test
Dataport Link- Blink Test
Durchgangsprüfung mit LED und Ton
Test Continuity by LED and audible
Widerstands Test durch Frequenzänderung
Resistance Test by changing audible tone
Low Batt - Anzeige durch blinkende LED
Low Batt indication by flashing LED
Automatische Abschaltung nach 45 Minuten
Auto shut Off after 45 minutes
Deaktivierung der Abschaltung
Auto shut Off override
Anzeige der Deaktivierung durch blinkende LED
Auto shut OFF override indication by flashing LED
Überspannungsschutz / Over Voltage Protection :
Bis zu 500V AC in TONE Modus / bis zu 240V AC in CONT Modus
Up to 500V AC in tone Mode / up to 240V AC in CONT Mode
Suchentfernung zum Kabel / Trace Distance to Cable/Wire :
Bis zu 60 cm / Up to 15” (60cm)
Maximale Kabellänge / Trace Cable Length :
Bis zu 15 km ohne Belastung / Up to 15 km (no load)
Hohe Sendeleistung (Batterie 9,2V) / High Power Output (Battery 9,2V) :
9,0V SS ohne Last / 9,0V PP no load
10 dBm into 600 Ohm
9 dBm into 150 Ohm
7,5 dBm into 75 Ohm
Ton auf kurzgeschlossener Ader bis 250 m
Tone over shorted pair up to 250 m. (Inhouse)
Weitere Leistungsmerkmale / Other Specifications:
Goldbeschichtete Kontakte
Gold Plated Contacts
Gerät Einschaltkontrolle mit LED
Unit ON - Indication by LED
Anzeige ALTernierende Frequenz mit blinkender LED
Indication of ALTernating Frequency by blinking LED
Anzeige SOLID Frequenz mit LED stehender LED
Indication of Solid frequencie by steady LED
Zugentlastung der Prüfschnüre
Test leads protected by rubber - strain relief
Getrenntes Batteriefach
Separate Battery Compartment
Batterie / Battery :
9V alkaline - Batterie >100 Stunden Lebensdauer
9V Alkaline, >100 hrs battery life
Abmessungen / Dimensions :
2.68” x 3.75” x 1.0” (68 x 96 x 25 mm)
Gewicht / Weight :
150 g ohne Batterie / 2.4 oz (150 g) without Battery
PROBE410
Gehäuse / Housing :
Solides, schlagfestes und wasserfestes ABS - Gehäuse
Heavy duty water resistant housing made from ABS.
Leistungsmerkmale / Specifications :
Nicht - Leitende Prüfspitze aus Kohlefaserverstärktem Kunststoff / Non-conductive solid carbon fiber tip
3,5 mm Kopfhörerbuchse
3.5 mm Earphone Jack
Goldbeschichtete Kontakte
Gold Plated Contacts
Getrenntes Batteriefach
Separate Battery Compartment
Rote LED zur ISDN Signalerkennung.
Red LED for ISDN signal indication
Batterie / Battery :
9V Alkaline Batterie >100 Stunden Lebensdauer
9V Alkaline, >100 hrs battery life
Abmessungen / Dimensions :
220 x 40 / 34 x 25 mm
8.7” x 1.57” / 1.34” x 0.98”
Gewicht / Weight :
80 g ohne Batterie
1.28 oz (80 g) without Battery
Download User Guide
Optional:
Light weight earpiece: to increase the sensitivity or reduce noise the Probe can be used with an earpiece.
Breakout adapter: no need to open any socket, the adapter connects clips to jacks. It allows alligator clips from Easytest to connect to specific terminals within modular jacks to monitor lines and make tests.
Download Datasheet (German)
EASYTEST720
Probe410
Solid belt pouch