User login
KE801 Fiber&Copper- Cable Finder Kit
The KE801 Kit (EASYTEST800/PROBE410) improves speed and confidence in the installation and maintenance of multimedia communications cabling.
EASYTEST800 can transmit either two continuous tracing tones (SOLID) or two alternating tones (ALT). The Solid or the Alt function is easily selected from the front panel using the ALT and SOLID buttons. An LED beside each button indicates the selected function. To stop the tone, use the OFF button. The unit can be connected to send the trace tone to any kind of cable, including a live telephone line. The unit is protected to 400 Vac in all modes.
EASYTEST800 provides an F-type coaxial connector, fiber-optic connector, durable alligator clips and a snag-proof RJ11 modular plug with strain relief for reliability. The special RJ11 modular plug has protection slots for pins 1 and 8 that will fit RJ45 jacks without damaging them. In the CONT position EASYTEST800 leads, F-connector and RJ11 plug will indicate short circuits (zero ohms to 40,000 ohms) with a green LED and an audible signal. In the OFF position EASYTEST800 will indicate the status of a connected telephone line including: service voltage presence and polarity, idle line, busy line, and incoming ringing.
The fiber-optic connector serves as a visible light source for identifying and finding faults in fiber cables.
The capacitive PROBE410 (U.S. PROBE310) is highly sensitive and works well with EASYTEST800 or any other tone generator to identify and trace wires or cables. The two-position HIGH and LOW volume switch is constructed with a highly dust and moisture resistant mylar membrane for easy, reliable operation. With the HIGH button depressed the PROBE410 can detect a traced cable at lateral distances of up to 100 cm. A more precise location of specific wires is usually done with the LOW button. No user experimentation with volume control knobs is needed.
The Probe410 has a special green LED indicator for use with Kurth EasyTest tone units. This indicator only lights when signals from EasyTest units are detected and has the effect of blocking interfering signals like power hum. The bright, color-correct LED on the probe snout eliminates the need for a separate flashlight in dark spaces.
The probe’s conductive tip is molded of a plastic and carbon fiber composite, preventing shorts and other disturbances to lines. This composite probe tip is nearly unbreakable and is easily changed without opening the case. The slender shape allows high precision tracing of pairs, whether in tight bundles or high density wiring blocks.
To increase audibility or reduce noise the Probe410 can be used with the optional, light-weight earpiece.
EasyTest KE800
Gehäuse / Housing :
Stabiles und schlagfestes wetterbeständiges ABS-Gehäuse mit Silikon Betätigungstasten / Heavy duty water resistant housing made from ABS, elastomeric silicon rubber push button switches.
Prüfschnüre / Test Leads: 25 cm lange Prüfschnüre aus flexiblem PVC mit 4mm Bananensteckern, eine Prüfleitung mit Modularstecker RJ11
(25cm) durable wire leads with 4mm bananaplugs and one with a special long modular plug RJ11 and latch protection
Vier Frequenzen wählbar / Four Frequencies
selectable :
1. SOLID: 1000 Hz
2. ALT: 1000/800 Hz
3. SOLID: 2600 Hz
4. ALT: 2600/1900 Hz
Genauigkeit / Accuracie < +/- 1% (Quartz)
Durchgangsprüfung mit LED und Ton
Test Continuity by LED and audible
Widerstands Test durch Frequenzänderung
Resistance Test by changing audible tone
Low Batt - Anzeige durch blinkende LED
Low Batt indication by flashing LED
Automatische Abschaltung nach 45 Minuten
Auto shut Off after 45 minutes
Deaktivierung der Abschaltung
Auto shut Off override
Anzeige der Deaktivierung durch blinkende LED
Auto shut OFF override indication by flashing LED
Überspannungsschutz / Over Voltage Protection :
Bis zu 400V AC/DC in TONE Betriebsart
Up to 400V AC/DC in tone Mode
Suchentfernung zum Kabel / Trace Distance to Cable/Wire :
Bis zu 60 cm / Up to 15” (60cm)
Maximale Kabellänge / Trace Cable Length :
Bis zu 15 km ohne Belastung / Up to 15 km (no load)
Hohe Sendeleistung (Batterie 9,2V) / High Power Output (Battery 9,2V) :
9,0V SS ohne Last / 9,0V PP no load
10 dBm into 600 Ohm
9 dBm into 100 Ohm
7,5 dBm into 50 Ohm
Ton auf kurzgeschlossener Ader bis 250 m
Tone over shorted pair up to 250 m. (Inhouse)
Glasfaser / Fiber
Laser Lichtquelle / Laser Source:
Wellenlänge / Wavelength 650 nm
Leistung / Optical Output Power <1 mW
Eingekoppelte Leistung / Fiber coupled power
Into singlemode fiber 9/125 µm max 600 µW
into multimode fiber 50/125 µm max 600 µW
Sendeart / Operating Mode Pulse ~ 1 - 2 Hz
Laser Protection Class 2
Ferrulenart / Suitable Ferrule 2,5 mm
DIN, E2000, FC, SC, ST
Weitere Leistungsmerkmale / Other Specifications:
Goldbeschichtete Kontakte
Gold Plated Contacts
Gerät Einschaltkontrolle mit LED
Unit ON - Indication by LED
Anzeige ALTernierende Frequenz mit blinkender LED
Indication of ALTernating Frequency by blinking LED
Anzeige SOLID Frequenz mit LED stehender LED
Indication of Solid frequencie by steady LED
Zugentlastung der Prüfschnüre
Test leads protected by rubber - strain relief
Getrenntes Batteriefach
Separate Battery Compartment
Batterie / Battery :
9V alkaline - Batterie >100 Stunden Lebensdauer Ton Modus
9V Alkaline, >100 hrs battery life Ton Modus
Optical Fiber Test < 5 Hours
Abmessungen / Dimensions :
2.68” x 3.75” x 1.0” (68 x 96 x 25 mm)
Gewicht / Weight :
150 g ohne Batterie / 2.4 oz (150 g) without Battery
PROBE410
Gehäuse / Housing :
Solides, schlagfestes und wasserfestes ABS - Gehäuse
Heavy duty water resistant housing made from ABS.
Leistungsmerkmale / Specifications :
Nicht - Leitende Prüfspitze aus Kohlefaserverstärktem Kunststoff / Non-conductive solid carbon fiber tip
3,5 mm Kopfhörerbuchse
3.5 mm Earphone Jack
Goldbeschichtete Kontakte
Gold Plated Contacts
Getrenntes Batteriefach
Separate Battery Compartment
Rote LED zur ISDN Signalerkennung.
Red LED for ISDN signal indication
Batterie / Battery :
9V Alkaline Batterie >100 Stunden Lebensdauer
9V Alkaline, >100 hrs battery life
Abmessungen / Dimensions :
220 x 40 / 34 x 25 mm
8.7” x 1.57” / 1.34” x 0.98”
Gewicht / Weight :
80 g ohne Batterie
1.28 oz (80 g) without Battery
Download User Manual
Optional:
Light weight earpiece: to increase the sensitivity or reduce noise the Probe can be used with an earpiece.
Breakout adapter: no need to open any socket, the adapter connects clips to jacks. It allows alligator clips from Easytest to connect to specific terminals within modular jacks to monitor lines and make tests.
Download Datasheet (German)
EASYTEST800
Probe410
Solid belt pouch