Professional sets for installation and troubleshooting with the ability to create individual test reports. The perfect solution for efficient work in active and passive networks.
Login to see pricesKE7207 comes with the active Network Tester KE7200 and the Cable Finder Kit KE701 Telco in a durable case including test cables, software and batteries.
The KE701 allows the user to precisely locate wire pairs or cables even inside walls or unmarked bundles.
Cable measurements and information about Ethernet performance can be stored and transfered to a PC or laptop. the included Windows PC-Software Ethernet-Mananger gives clear indication about cable length, cable faults and allows the creation of subscribers measurement logs.
| KE401, KE701 & KE801 Probe | |
|---|---|
| Functions | 1 kHz filtered signal detection LED Torch light function ISDN signal detection LED |
| Reach | Trace distance to cable/wire up to 60 cm |
| Dimensions / Weight | 220 x 40/34 x 25 mm / 80 g without battery |
| Additional Features | Exchangeable non-conductive solid carbon fiber tip 3.5 mm earphone jack Gold plated contacts Separate battery compartment |
| KE701 Telco Kit Tone Generator | |
|---|---|
| Durable wire lead length | 25 cm |
| Lead connectors | 2x banana with alligator clips 1x long RJ11 plug 1x RJ45 plug |
| Functions | Continuity test through LED + Tone Resistance test through frequency change Low Batt indication by flashing LED Auto shut off after 45 minutes Auto shut off override Unit ON indication by LED Indication of ALTernating freq. by flashing LED Indication of SOLID freq. by steady LED Data Port test with HUB-Blink |
| Search frequencies | 6 frequencies selectable SOLID: 1000, 2600, 577.5 Hz and ALT: 1000/800, 2600/1900, 577.5 intermittent Accuracy <±1% (quartz) |
| Reach | Trace cable length up to 15 km (no load) Tone over shorted pair up to 250 m |
| Transmitting Power | High power output with 9.2 V battery : 9.0 V PP no load 10 dBm into 600 Ohm 9 dBm into 100 Ohm 7,5 dBm into 50 Ohm |
| Overvoltage Protection | 500 V AC/DC |
| Dimensions / Weight | 68 x 96 x 25 mm / 150 g without battery |
| Additional features | Test leads protected by rubber-strain relief Gold plated contacts Separate battery compartment |
| KE7010 Remote Unit | |
|---|---|
| Features | ID programmable 01 - 32 LED indicates good / bad |
| Housing | Solid and weather protected ABS |
| Dimensions | 61 x 41 x 26 mm |
| Weight | 30 g |
| KE7200 | |
|---|---|
| Wire test copper | Check of wires connected to PIN and Pair Detects split pair from 6 ft (2 m) on 16 dedicated wiring schemes predefined, user settable via device 16 cable types with predefined VP values, user settable via device Graphical display shows wire map with clear indication good/bad Measures all wires separately and shows length to fault short/open up to 150 m (TDR) |
| Power over Ethernet Test | Activation of PoE/PoE+ port (IEEE 802.3af/at) Measuring of voltage and current. Shows available power in watts |
| Cable Trace | Hub-Link Blink Function Trace tones to be detected by capacitive Probe (optional) 4 tones selectable |
| IP Network Testing | Checks network with static IP or by DHCP Detect the network speed 10/100/1000 Mbit IP address and MAC address settable Listing of all working stations by name, IP and MAC address Ping of selected addresses - frame settable between 32 and 1024 Bit Shows result number of pings, lost pings, time min/max/average Constant ping mode to generate traffic |
| Bridge Tap (optional) | Detects and locates Bridge Taps |
| Overvoltage protection | Up to 100 Volt |
| Housing | Solid and weather protected ABS with drop protection, IP52 |
| Battery | 4 x 1.5 V Alkaline (AA) > 40 hrs operating time |
| Dimensions | 195 x 100/78 x 45 mm |
| Weight | 380 g without battery |
| Menu language | German, English |
| Environment | Working temperature 0° – +50°C Storage temperature -25° – +75°C Humidity 90%, non-condensing |
| KE701 Telco Kit Data Sheet (DE/EN) |
 408.96 KB
|
| KE301-KE801 Manual (DE/EN) |
1.32 MB
|
| KE7200 PoE++ Data Sheet |
914.63 KB
|
| KE7200 short operating manual |
271.88 KB
|
| KE7200 PoE++ operating manual |
796.43 KB
|
| KE7x0x Data Sheet |
784.52 KB
|
| Kurth Electronic Program 2018 |
12.72 MB
|
The KE6000 is a simple, affordable, fast and efficient network cable tester. KE6000 can test UTP and STP patch cables and by using two units, also telecom and data cables. The KE6000 is simple to use with the large and easy to read LCD display readouts, indicating cable faults or verifying cable and pin-out-integrity. The fault is shown as a clear information – no need to watch and count flashing LEDs.
....
The ideal set for the daily work in all types of networks without the need for documentation. Saves time and money during installation and maintenance.
....
Set of four Remote units, short patch cables, Search Signal Reciever Probe310 and pouch for KE7100 and KE7200.
....
The KE7100 LANcheck is an easy to use, handy and cost-effective LAN Tester. The little brother of the KE7200 Ethernet Performance Tester is ideal for measurements in networks where documentation is not required or necessary.
....